Cally functionalized micropores can be used for selective capture of individual micrometric objects. This strategy has been evidenced using cODN-modified PS microparticles, and then extended to living primary cells. B or T lymphocytes have been selectively isolated from a splenocyte suspension using micropores modified by specific antibodies. As a result of the geometric restriction of the pore, a high probability of physical contact between the flowing cells and the functionalized surface is ensured. This approach may provide a simple way for individual cell sorting from a complex sample, by ensuring selective and spatially controlled cell capture. It has potential applications for individual cell analysis by immobilizing and optically detecting individual target cells 23977191 at desired positions, then detaching them using enzymatic cleavage of a specific restriction site present in the ODN sequence, as demonstrated by some of us recently [14]. The released cells collected in the bottom compartment by sedimentation may be MedChemExpress CY5-SE subject to further examination [38?3]. In addition, the capture of other biological objects, e.g. bacteria, should be possible by decreasing the pore size to that of the targeted biological objects. Possible applications of in-situ bacteria detection include fast identification and quantification of bacteria in clinical or environmental samples. Given the possibility of one-step multi-pore functionalization, the employment of locally functionalized micropore arrays might also open up new possibilities for high-throughput sorting and collection of rare cells. High detection sensitivity may be provided by the compelled movement of the cells close to the probes in the micropores, which might be especially useful to reveal cells present at low ratio in the suspension. We therefore anticipate that the approach described herein will be useful for fundamental research in individual cell analysis as well as a detection platform for diagnostic applications. To achieve these goals, an array of biofunctionalized micropores is preferred to a single micropore approach in order to simultaneously prevent definitive blockade by only few cells, reach a high throughput of sample analysis, observe collectively the whole set of trapped cells using wide field-of-view imaging [60,61], and possibly vary functionalization coatings and thus capture possibilities.using backside lithography, reactive ion etching (RIE) and KOH etching. A scalloped micropore of 19 mm in diameter was then etched by deep RIE in each silicon membrane. Steam oxidation of silicon at 1050uC during about 2 days formed a 4-mm-thick silicon oxide layer on the whole chip surface, including the micropore wall, which reduced the pore diameter to 15 mm and increased the membrane thickness to 10 mm (Figure 1).Micropore FunctionalizationThe functionalization of micropores with PPy-ODN copolymer has been described previously [55,56], and is detailed in Supporting Information (Text A and Text B in File S1). Briefly, the micropores to be specifically functionalized were placed between two compartments filled with an electrolytic solution containing MedChemExpress CUDC-907 pyrrole and pyrrole-ODN (Table S1 in File S1). A platinum electrode was immersed in each compartment. PPyODN copolymer was only electro-polymerized on the micropore inner wall upon application of 2 V for 100 ms supplied by a potentiostat SP?00 from Bio-Logic (Claix, France). To functionalize the micropores with cell-specific antibodies, PPy-OD.Cally functionalized micropores can be used for selective capture of individual micrometric objects. This strategy has been evidenced using cODN-modified PS microparticles, and then extended to living primary cells. B or T lymphocytes have been selectively isolated from a splenocyte suspension using micropores modified by specific antibodies. As a result of the geometric restriction of the pore, a high probability of physical contact between the flowing cells and the functionalized surface is ensured. This approach may provide a simple way for individual cell sorting from a complex sample, by ensuring selective and spatially controlled cell capture. It has potential applications for individual cell analysis by immobilizing and optically detecting individual target cells 23977191 at desired positions, then detaching them using enzymatic cleavage of a specific restriction site present in the ODN sequence, as demonstrated by some of us recently [14]. The released cells collected in the bottom compartment by sedimentation may be subject to further examination [38?3]. In addition, the capture of other biological objects, e.g. bacteria, should be possible by decreasing the pore size to that of the targeted biological objects. Possible applications of in-situ bacteria detection include fast identification and quantification of bacteria in clinical or environmental samples. Given the possibility of one-step multi-pore functionalization, the employment of locally functionalized micropore arrays might also open up new possibilities for high-throughput sorting and collection of rare cells. High detection sensitivity may be provided by the compelled movement of the cells close to the probes in the micropores, which might be especially useful to reveal cells present at low ratio in the suspension. We therefore anticipate that the approach described herein will be useful for fundamental research in individual cell analysis as well as a detection platform for diagnostic applications. To achieve these goals, an array of biofunctionalized micropores is preferred to a single micropore approach in order to simultaneously prevent definitive blockade by only few cells, reach a high throughput of sample analysis, observe collectively the whole set of trapped cells using wide field-of-view imaging [60,61], and possibly vary functionalization coatings and thus capture possibilities.using backside lithography, reactive ion etching (RIE) and KOH etching. A scalloped micropore of 19 mm in diameter was then etched by deep RIE in each silicon membrane. Steam oxidation of silicon at 1050uC during about 2 days formed a 4-mm-thick silicon oxide layer on the whole chip surface, including the micropore wall, which reduced the pore diameter to 15 mm and increased the membrane thickness to 10 mm (Figure 1).Micropore FunctionalizationThe functionalization of micropores with PPy-ODN copolymer has been described previously [55,56], and is detailed in Supporting Information (Text A and Text B in File S1). Briefly, the micropores to be specifically functionalized were placed between two compartments filled with an electrolytic solution containing pyrrole and pyrrole-ODN (Table S1 in File S1). A platinum electrode was immersed in each compartment. PPyODN copolymer was only electro-polymerized on the micropore inner wall upon application of 2 V for 100 ms supplied by a potentiostat SP?00 from Bio-Logic (Claix, France). To functionalize the micropores with cell-specific antibodies, PPy-OD.